Table of Contents

PS 1 - General

1.1 - General

1.2 - Standards and Guidelines

1.3 - Shop Drawings

1.4 - Warranty

1.5 - Training

1.6 - Approved Products

PS 2 - Operator Interface

2.1 - Access Requirments

2.2 - Access Security

2.3 - Modem Requirements

2.4 - Operator Interface Software

2.5 - Executing the Dynamic Color Graphics

2.6 - Static Screen Graphics Generation Software

2.7 - Operator Interface Hardware Standards

2.8 - Temporary Operator Interface

PS 3 - Programmability

3.1 - Database Creation and Modification

3.2 - Alarm Definition and Processing

3.3 - Trends

3.4 - Trend Graphing

3.5 - Totalization

3.6 - Scheduling

3.7 - Point Definitions

.1 - Analog Points

.2 - Digital Points

3.8 - Software Controlers

3.9 - Operator Control Language (OCL) Capabilities

3.10 - OCL Editor

PS 4 - Intra-system Communication

4.1 - Network Communications

.1 - Stand-Alone Panels (SAPs)

.2 - Terminal Unit Controllers (TUCs)

4.2 - System Display and Processing Speed

PS 5 - Hardware Features

5.1 - Power Conditioning

5.2 - Power Failure Protection

5.3 - Hardware Failure Isolation

5.4 - Ease of Hardware Replacement

5.5 - Database Back-Up and Off-Line Storage

5.6 - Memory

5.7 - SAP Processing Speed

PS 6 - Field Devices

6.1 - General

6.2 - Point Type ``CRS''

6.3 - Point Type ``CR1''

6.4 - Point Type ``CR2''

6.5 - Point Type ``CR3''

6.6 - Point Type ``CS1''

6.7 - Point Type ``CS2''

6.8 - Point Type ``CV1''

6.9 - Point Type ``CV2''

6.10 - Point Type ``CV3''

6.11 - Point Type ``CV4''

6.12 - Point Type ``DA1/x''

6.13 - Point Type ``DA2/x''

6.14 - Point Type ``DA3/x''

6.15 - Point Type ``DA4/x''

6.16 - Point Type ``DDC''

6.17 - Point Type ``DHS''

6.18 - Point Type ``DPS/x''

6.19 - Point Type ``DTS1/x''

6.20 - Point Type ``DTS2''

6.21 - Point Type ``FRZ''

6.22 - Point Type ``GAS1''

6.23 - Point Type ``GAS2''

6.24 - Point Type ``GAS3''

6.25 - Point Type ``GAS4''

6.26 - Point Type ``GAS5''

6.27 - Point Type ``LS1''

6.28 - Point Type ``LS2''

6.29 - Point Type ``OS1''

6.30 - Point Type ``OTS''

6.31 - Point Type ``PS1''

6.32 - Point Type ``PTS1''

6.33 - Point Type ``PTS2''

6.34 - Point Type ``RHS''

6.35 - Point Type ``RTS1''

6.36 - Point Type ``RTS2''

6.37 - Point Type ``RTS3''

6.38 - Point Type ``VS1''

6.39 - Point Type ``VS2''

6.40 - Point Type ``WPS''

PS 7 - Operating System Software Point Requirements

7.1 - General

7.2 - Point Type "AL"

7.3 - Point Type "AS"

7.4 - Point Type "CO"

7.5 - Point Type "PG"

7.6 - Point Type "TL"

7.7 - Point Type "TZ"

7.8 - Point Type "V"

7.9 - Point Type "WS"

PS 8 - Installation Standards

8.1 - General

8.2 - Calibration

8.3 - Electrical Work By The Controls Contractor

8.4 - Electrical Work by the Electrical Contractor (DIV 16)

8.5 - Conduit, Wiring and Cabling

8.6 - Control Hardware

8.7 - Installation of Control Devices

8.8 - Installation of Actuators

PS 9 - Substantial Performance Test Procedures

9.1 - Overview

9.2 - During SEVEN (7)-Day Test

9.3 - Training and Demonstrations

9.4 - Documentation

9.5 - Project Acceptance

---

[ Previous Section || Table of Contents || Overview || Next Section ]

[ Comments || Disclaimer ]